A seam on the back wall a bathtub has will often be seen where the tub's flange meets its backer board. This seam is often sealed with caulk. You may have to patch some areas if the seam is not sealable. If you're installing a new tub surround over this area, make sure to follow the proper procedures to prevent damage to the drywall.
The tub surround should be level at the back. The old tub surround must be removed before you begin installing the new one. This can be done using a prybar, or a tool like a hammer. Also, be sure to wear protective gear.
A tub surround can be installed over concrete, tile or wood depending on your needs. You can purchase these surrounds in a variety of styles and colors. These surrounds are most commonly made of acrylic or plastic panels. Each type of panel has its own installation instructions. Some kits include only one back panel, others include two. You can save money by purchasing a single-piece surround.
After you have removed the old surround, remove the corner panels. Next, measure the new surround and determine its dimensions. It is crucial to use the right adhesive for it to stick. You will need to apply adhesive to multiple sections at once, so give it plenty of drying time.
When you're ready to start applying the adhesive, mark the left and right sides of your wall and the top and bottom of the surround. This will provide you with a visual guideline for where to apply adhesive. It is important to accurately cut the adhesive lines. Masking tape can be used for making the lines visible.
Next, place the surround's backpiece against the wall. Finally, adjust the back to make it flush. The back should be flat against the drywall. If the back piece is not level, you'll need to add some extra adhesive to the gap. After applying the adhesive, you'll need to let it dry for at least 24 hours.
Now it's time to put the tub surround back wall in place. This is the most straightforward part. It's best to have someone hold it to ensure that it doesn't move. Alternately, you could place a line across the surface and use that to guide your installation.
You will attach the end flanges on the studs. You should drive fasteners through predrilled holes that are slightly larger than the actual size. For added support, add a few 2x4 nailers. They should be attached to drywall, but they shouldn't be directly attached to the wall framing.
Before you start tiling you'll need to put on the appropriate vapor barrier. A vapor barrier, which is thick plastic sheeting, protects the wall against moisture. In addition, you'll need to apply primer and paint. There are many types of glue available. For more information, please refer to the manufacturer's instructions.
FAQ
Is it cheaper to build a new house or remodel an old one?
There are two choices if you are thinking of building a new house. One option is to buy a pre-built home. This type home is already constructed and ready for you to move in. Another option is to build a custom home yourself. If you choose this option, you will need to hire someone to help you design your dream home.
How much time and money it takes to design and plan a new house will affect the cost. A custom home may require more effort because you'll likely need to do most of the construction work yourself. But you can choose the materials you want and where you want them to be placed. So, it might be easier to find a contractor who specializes in building custom homes.
A new house is generally more expensive than a home that has been renovated. You'll have to pay more for land and any improvements. In addition, you will need to pay permits and inspections. On average, the difference in price between a new and remodeled house is $10,000 to $20,000.
How do you make a house look new?
These are the steps to follow when renovating your house without spending a lot of money.
-
Make a budget plan
-
Find out what materials are required
-
Decide where to put them
-
Make a list of things you need to buy
-
Calculate how much money is available
-
Plan your renovation project
-
Get started on your plans
-
Online research is a good idea.
-
Ask your family and friends for assistance
-
Get creative!
How do you choose a good contractor to work with?
Ask your family and friends for recommendations when choosing a contractor. You can also look online for reviews. Look online for reviews to ensure the contractor you choose is experienced in the construction area you are interested. Ask for references and check them out.
Statistics
- On jumbo loans of more than $636,150, you'll be able to borrow up to 80% of the home's completed value. (kiplinger.com)
- Design-builders may ask for a down payment of up to 25% or 33% of the job cost, says the NARI. (kiplinger.com)
- ‘The potential added value of a loft conversion, which could create an extra bedroom and ensuite, could be as much as 20 per cent and 15 per cent for a garage conversion.' (realhomes.com)
- Rather, allot 10% to 15% for a contingency fund to pay for unexpected construction issues. (kiplinger.com)
- They'll usually lend up to 90% of your home's "as-completed" value, but no more than $424,100 in most locales or $636,150 in high-cost areas. (kiplinger.com)
External Links
How To
How do I plan a whole house remodel?
Research and careful planning are essential when planning a house remodel. Before you start your project, there are many factors to consider. First, you must decide what type of home improvement you want. There are many options available, including kitchen, bathroom and bedroom. Once you've chosen the category you want, you need to decide how much money to put towards your project. It's best to budget at least $5,000 per room if you don't have any experience working on homes. If you have experience, you may be able to manage with less.
Once you have figured out how much money you can afford to spend, you'll have to determine how big of a job you want to tackle. If you have only enough money to remodel a small kitchen, you may not be able add new flooring, countertops, or paint the walls. You can do almost everything if you have enough cash for a full-scale kitchen renovation.
Next, find a contractor that specializes in the project you are interested in. This will guarantee quality results, and it will save you time later. After you have selected a professional contractor, you can start to gather materials and supplies. You may need to purchase everything from scratch depending on the size and scope of your project. You shouldn't have any trouble finding the right item in pre-made stores.
Once you've collected all the materials you will need, you can begin to plan. To begin, draw a sketch of where you would like to place furniture or appliances. Next, plan the layout. Make sure that you leave space for plumbing and electrical outlets. It is a good idea to place the most important areas nearest the front door. This will make it easier for visitors to access them. Last, choose the colors and finishes that you want to finish your design. Avoid spending too much on your design by sticking to simple, neutral colors and designs.
Now it's time for you to start building. It's important that you check the codes in your area before you start construction. While some cities require permits, others allow homeowners to construct without them. To begin construction you will first need to take down all walls and floors. Next, you'll lay down plywood sheets to protect your new flooring surfaces. You will then attach or nail pieces of wood together to make the cabinet frame. You will attach doors or windows to the frame.
You'll need to finish a few final touches once you're done. You will likely need to cover exposed wires and pipes. Plastic sheeting and tape are used to cover exposed wires. Mirrors and pictures can also be hung. Keep your work area tidy and clean at all times.
These steps will ensure that you have a beautiful and functional home, which will save you tons of money. Now that you know how to plan a whole house remodeling project, you can go ahead and get started!