
Installing tongue and groove paneling over drywall is a popular way to add character and beauty to a room. You have many options for how to install this type paneling. However, all of them require accurate measuring and cutting. One common method is to nail panels directly onto furring strips that run vertically down the wall. Another method is to install diagonally, using a 45-degree angle cut at both ends of each panel to form the long groove side.
Installation Steps
Wood planks should be mounted over drywall. To do this, remove any outlets, hooks or nails. Sand any wall protrusions. To accomplish this task, you can use a power or large sandpaper section and an extension base.
Determine whether your tongue and groove paneling is nailed to drywall or studs
Placing a prybar at the corner of two walls is a good way to verify that the tongue and groove wall panels have been nailed to the drywall. Use your hammer to gently tap the prybar into the seam between the walls. If the panel is not nailed to drywall you will need to pull it off the wall using a prybar or pliers.

Find out if your tongue-and-groove wall panels are nailed on or glued.
Once you've determined that your paneling is nailed to drywall, begin by removing any trim that's still attached to the wall. The trim can be reused if you are able, so do your best to not damage it.
If the trim is not recyclable, you will have to buy new wood paneling. You will need four sheets of 4'x8" wood paneling to cover the walls you want. Measure the wall width and divide that number by 4. For walls taller than 8ft, you'll need half a panel to cover each door and quarter panel for each windows.
Drywall: Marking a straight edge
Make sure your wood paneling runs evenly along the drywall surface. Run a straight edge down the wall side-to-side to make sure it is. In areas where the paneling is not flush with the drywall, such as corners or over window frames and doors, you should be looking for a protrusion of drywall. If the drywall bulges or sticks out, your paneling may not lay flat.
Use a Dust Mask to Sand Drywall
When you're installing tongue and groove paneling over drywall, sand down any areas where the drywall protrudes. This will allow your paneling to be installed more easily and evenly.

Finishing with Wood Puffin
Once the drywall has been sanded, you can apply a coat wood putty on the walls and paneling to seal any joints between them. The paneling can also be stained with a wood stain for a more natural look. However, this requires more labor than applying paint.
Attaching Paneling to Drywall
You will need a nail set that has rounded heads to attach wood paneling and drywall. These fasteners can be purchased at most hardware shops and cost approximately $4 for a pack of 16-penny common nail. They can be used on any type of wood such as plywood or drywall. However, they are not recommended for use with thicker boards.
FAQ
Do you prefer to do walls or floors first?
The best way to start any project is by deciding on what you want to achieve. It is essential to consider how the space will be used, who will use it, and why. This will help you decide if you should go for flooring or wall coverings.
You can choose to put flooring in the first place if you decide to open up your kitchen/living space. You could also consider wall coverings for privacy if this is the space you are looking to create.
Can I rent a dumpster?
A dumpster can be rented to dispose of your debris after you have completed your home renovation. Renting out a dumpster is an excellent way to keep your yard tidy and free from debris.
What room do I need to remodel first?
The heart of any home is the kitchen. It's where you spend most of your time eating, cooking, entertaining, and relaxing. If you're looking to make your kitchen more functional, attractive and beautiful, this is the place for you!
The bathroom is also an important part of any home. It is a place where you can feel at ease and privacy as you perform daily tasks such as brushing teeth, bathing, shaving, and getting ready for sleep. If you want to improve the functionality and appearance of these rooms, consider adding storage space, installing a shower instead of a tub, and replacing old fixtures with modern ones.
Statistics
- Most lenders will lend you up to 75% or 80% of the appraised value of your home, but some will go higher. (kiplinger.com)
- It is advisable, however, to have a contingency of 10–20 per cent to allow for the unexpected expenses that can arise when renovating older homes. (realhomes.com)
- They'll usually lend up to 90% of your home's "as-completed" value, but no more than $424,100 in most locales or $636,150 in high-cost areas. (kiplinger.com)
- According to the National Association of the Remodeling Industry's 2019 remodeling impact report , realtors estimate that homeowners can recover 59% of the cost of a complete kitchen renovation if they sell their home. (bhg.com)
- Design-builders may ask for a down payment of up to 25% or 33% of the job cost, says the NARI. (kiplinger.com)
External Links
How To
How to renovate an older house
First, you need to decide what kind of renovation you want. This could be anything from updating your kitchen appliances to completely renovating the house.
Once you have decided what type of renovations you want to undertake, the next step is to determine how much money it will cost. You might find that you don't actually have enough funds to cover the full cost of the entire project. This could mean that you have to make tough decisions about which parts of your house you can afford and which you cannot.
Before you make the decision to carry out renovations, there are some things that you should do. You must ensure you have all the permits needed for the job. You should also check whether you require planning permission for certain types of work. To add extensions to your home or make other changes, you might need building consent.
Before you start work on the house it is best to check with the local council website to determine if additional permits are required. It is also important to check whether planning permission is required for every part of the house you are renovating. For major projects like a new roof installation, your insurance provider may need to be contacted to confirm that you have adequate coverage.
The next step after obtaining all necessary permits is to pick the right materials and tools for the job. You have many options. It is important to carefully research all of them. Most people use wallpaper paste, paint, flooring, tiles and carpets for their renovation projects.
Be sure to consider the product's quality when choosing these products. Cheap products tend to last only a short period of time, whereas good quality products will usually last longer and provide better value for money. When buying anything, it's important that you buy the right amount for the job. Don't purchase too much as it can lead to waste of resources and the need for a lot of material. Try to only buy what you actually need.
After you've selected the right materials for your job, you should plan where to store them while working on the property. If you're remodeling a large portion of the house, you may need to rent storage space to store your materials until you're ready for them to be returned inside. You might also consider asking family and friends to move your belongings around.